Ahh, but the Bullseye washers were too thin when using 2, and too thick when using all 4 (2 per side). When using a 7/8 speed chain, you could use 2 (1 per side), but the NR/SR bolt heads would protrude a bit. I guess it wasn't only standard bearings, but also standard washers. The obvious solution is machining custom washers...
Also, the aluminum pulleys are noisy, plus they wear faster than
plastic. Still, I raced with them for many years with good results.
Not a single race I did not finish due to pulley failure ;-)
--
Jan Heine, Seattle
Editor/Publisher
Vintage Bicycle Quarterly
http://www.mindspring.com/
>Bullseye pulleys were indeed supplied with four washers. One washer was
>used on each side of each pulley in order to space the cages further apart.
>I believe the reason this was done was due to the fact that the pulley
>bearings were standard dimension (O.D. and I.D.) sealed bearings which for
>their given I.D and O.D. are only available in one width unless you special
>order them. At the rate they were sold I presume that it was an economic
>issue - less expensive to include 4 washers; much more expensive to use
>bearings of a non-standard size.
>
>Eric Elman
>Somers, CT
>just replaced 4 Bullseye pulley bearings two months ago.
>
>----- Original Message -----
>From: "jerrymoos" <jerrymoos@sbcglobal.net>
>To: "r cielec" <teaat4p@yahoo.com>; <classicrendezvous@bikelist.org>
>Sent: Thursday, April 22, 2004 6:27 PM
>Subject: Re: [CR]Replacement Pulleys for NR?
>
>
>> Been a while since I installed Bullseye pulleys, but I think you just used
>> the original Campy pulley bolts and shimmed with small washers. In fact,
>I
>> think the little washers came with the Bullseye pulleys. I don't know why
>> they didn't just make the pulleys thicker.
>>
>> Regards,
>>
>> Jerry Moos
>> Houston, TX
>>
>>
>> ----- Original Message -----
>> From: "r cielec" <teaat4p@yahoo.com>
>> To: <classicrendezvous@bikelist.org>
>> Sent: Thursday, April 22, 2004 2:42 PM
>> Subject: [CR]Replacement Pulleys for NR?
>>
>>
>> > Ahoy:
>> > Any suggestions for good replacement pulleys for NR rear derailluers and
>5
>> or 6 spd friction? This would use a traditional friction width type chain,
>> say a Sram PC 48, or such.
>> > LBS over the counter pulleys all seem to be too narrow. And, several
>years
>> ago a technician from Campag, California, advised me not to use Bullseye
>as
>> they are too narrow. Thought of using washer-shims to increase distance
>> between plates but, could not find long enough pulley bolts. How's that
>for
>> the nuts?
>> > See, you folks with bike shops and bins of little stuff have such an
>easy
>> time of it - just grab it, try it, try something else. I only wish....
>> > Thanks
>> > Richard Cielec
>> > Chicago, Illinois
>> >
>> >
>> > ---------------------------------
>> > Do you Yahoo!?
>> > Yahoo! Photos: High-quality 4x6 digital prints for 25ยข
>> >
>> > --- StripMime Report -- processed MIME parts ---
>> > multipart/alternative
>> > text/plain (text body -- kept)
>> > text/html
>> > ---
>> > _______________________________________________
>> > Classicrendezvous mailing list
>> > Classicrendezvous@bikelist.org
>> > http://www.bikelist.org/
>> >
>>
>>
>> _______________________________________________
>> Classicrendezvous mailing list
> > Classicrendezvous@bikelist.org
> > http://www.bikelist.org/