I use the nuts as a washer on water bottle cages. I have built several bikes that needed to have the cage raised above the front derailleur clamp. Works great and seem to have plenty hanging around.
Gary Smith Raleigh NC USA
Sent via BlackBerry by AT&T
-----Original Message----- From: "Charles T. Young" <youngc@ptd.net>
Date: Thu, 4 Jun 2009 06:08:21 To: <classicrendezvous@bikelist.org>; ternst<ternst1@cox.net> Subject: Re: [CR] Presta Plastic Valve Caps ?? - Oops
Ted:
I'm with you, pal. Valve caps do seem to be yet another example of a solution in search of a problem.
At least the "dork nuts" can be pressed into service here and there. I've used them to hastily fit a pair of mudguards recently without having to remove the fixing nut on brake caliper centerbolts because the threading matches. I've also had occasion to ream out the threading with a chainsaw file and use them as bushings to mount a pair of conventional nutted brakes to a frame set up for recessed mounting. After removing threading and enlarging the ID a bit, they can also be used as spacers to fit a front brake caliper to a rear brake bridge by stacking out to the threaded portion so the fixing nut can grab. Definitely a bit of a bodge but it works and saves one from having to remove the chroming, run a die over the unthreaded portion and cutting to length.
Any other examples out there for adaptive reuse of those little knurled nuts?
Charlie Young
Honey Brook, Pennsylvania USA
<r.clair@cox.net>; "Wayne Bingham" <blkmktbks@gmail.com> Cc: <classicrendezvous@bikelist.org> Sent: Wednesday, June 03, 2009 11:57 PM Subject: Re: [CR] Presta Plastic Valve Caps ?? - Oops
> Well guys and gals:
> Now your talking bling.
> If you wish a show bike then by all means pimp it out.
> If you wish to recreate or have a working bike then throw them in your
> unused stolen hotel ashtray.
> When you flat and have remove the tire in a hurry, there is no time to
> waste removing valve caps, unless your team car is there with a new wheel.
> Even out on a training or plain ol' ride, who wants to bother undoing caps
> and putting them back on, spares and /or original, especially if it's cool
> and you have stiff fingers.
> About the only way a cap comes in handy is if the tire/tube is in a holder
> and the cap would keep the valve point from putting a hole in the
> casing/tube.
> But a cap could rub thru too.
> Of course, the caps come in handy if you wedge them into your hand pump
> valve grommet and then shoot it out at someone across the room. Carefule
> tho, don't hit anyones eyes.
> The same goes for the little outside valve nut.
> When air goes out of the tube it draws the valve into the casing and that
> nut titens up. Often it is so tite that it can't be easily be undone with
> fingers.
> Naturally, the next vehicle will come along and stop to offer you their
> toolkit. NOT.
> Back in the 50's thru '70's most everyone in the know tossed the QR
> springs away also.
> They could jam in the dropouts ore between the axle hole and skewer rod
> When you pulled the wheel into position you would have the QR lever in
> hand and move it right into center. The springs' centering effect was
> useless.
> This was common knowledge among all the coaches, trainers, mechanics, and
> riders I knew and it wasn't even discussed, just done.
> With the neocon invasion, much lore and sound practices were
> forgotten/lost.
> So as nice as these things are, consider your machine's purpose and equip
> accordingly. If you ride it then you know and can educate your colleagues,
> If the machine is being shown, then a little card on the display
> identifying these areas wll enlighten the spectators, make the bike more
> accurate for judging, and give you the satisfaction of having a real bike
> true to it's purpose in your classic stable.
> Ted Ernst
> Palos Verdes Estates
> CA USA